Скачать с ютуб 面包机 换皮带 教程 Bread Maker Belt Replacement | Change Belt | DIY SKG 3930 в хорошем качестве

面包机 换皮带 教程 Bread Maker Belt Replacement | Change Belt | DIY SKG 3930

Bread Maker Belt Replacement | Change Belt | DIY SKG 3930 面包机 换皮带 教程 More Pre-Ferment Dough Methods 4种面包面种法: 👉🏻 液种/波兰种法 Chilled Pre-Ferment Dough Method:    • 波兰种 液种 详细做法解释 Chilled Pre-Ferment Dou...   👉🏻冷藏中种法 Chilled Zhong Zhong Pre-Ferment Dough Method:    • 冷藏中种法 详细解释 Chilled Zhong Zhong Pre-Fe...   👉🏻100%中种法 100% Zhong Zhong Pre-Ferment Dough Method:    • 100% 中种法详细做法 100% Zhong Zhong Pre-Fer...   👉🏻烫种法 Tang Zhong Pre-Ferment Batter Method:    • 汤 (烫) 种法详细做法介绍 Tang Zhong Pre-Ferment...   Subscribe for more videos: YouTube 👉🏻 Jacelyn Lim Recipes Sharing👈🏻    / jacelynlim   YouTube 👉🏻 Jacelyn & Xuan Foods and Travel Vlog👈🏻 https://bit.ly/394HX4J Follow Jacelyn on social media: Facebook:   / imjacelynlim   Instagram:   / imjacelyn   #imjacelyn #breakmaker #面包机 #换皮带 工具 Tools: 24cm 平面螺丝刀 flat screwdriver 24cm 十字螺丝刀 closed screwdriver 剪刀 scissor 油漆刷 brush 1。拆除面包机盖子。 Remove the cover of the bread maker. 2。用平面螺丝刀，拆除底部螺丝。 Using the flat screwdriver to unscrew the bottom part. 3。拆除面包机上的4颗灰色软盖 + 9颗螺丝。 Remove the 4 grey soft covers + 9 screws from the upper part. 4。拆除面包机上的方形铁片。 Remove the square piece of iron. 5。握着机身后端的桃红色外壳，往上轻拉(不要过度用力，下面有电线连接着）把整个桃红色外壳拆除。 Hold the pink case at the top back of the bread maker, pull out gently (be caution, there are wires below) to remove the entire pink case. 6。把桃红色外壳，依靠着机身，斜放在比较高的地方，不要拉扯到电线！ Place the pink case beside the bread maker (be caution of the wires) 7。拆除前端的4颗螺丝。 Remove the 4 screws at the front. 8。接着拆除后端的3颗螺丝。 Then remove the 3 screws at the back. *后端中间的那颗接着黄绿色电线的螺丝，有着2片非常小片的铁片配件，不可弄丢了！ There is a yellow-green wire connected with a screw, with 2 very small pieces of accessory, do not lose it. 9。螺丝拆除后，即可把整个底座拿起。*慢慢地拉开，有电线连接着。 After all the screws are removed, slowly pull the base out. 10。底座拿起后，既可以看到转轮上有个皮带 You will see the broken belt at the base. 11。把皮带 (或有些皮带已经被使用至只剩下一条白色的线) 剪掉。 Cut off the broken belt. 12。用刷子清理底座。 Clean the base with a brush. 13。再把新皮带安装上去。先把新皮带安装在小轮子后，接着拉向大轮子，旋转大轮子，皮带就会慢慢的被卷入大轮子中。 Then install the new belt. First place the new belt on the small spindle, then pull towards the big spindle, spin the big spindle, until the belt fits nicely onto the spindle. 14。试转动轮子看看是不是顺畅的。 You can then give it a couple of spins to make sure it's on correctly and rotates smoothly. 15。现在把所有机件安装回去。 Now, install all the accessories back into the bread maker. 16。首先把机身后端，有条黄绿色电线上的螺丝锁上: 先把有条纹的铁片放在螺丝洞口上。 First, place the small piece of black stripe on the middle hole. 17。然后放上黄绿色电线接口。 Place the yellow-green wire on it. 18。最后放上平面铁片，再把螺丝锁好。 Then place the flat piece of iron on it and screw it in. 19。之后，把其它两个螺丝装上。 After that, install the other two screws. 20。现在把前端的4颗螺丝装上 Now install the 4 screws on the front. 21。然后把桃红色外壳安装好。 Fix the pink case. 22。把方形铁片安装好 Fix the square piece of iron. 23。锁上9颗螺丝 + 4颗灰色软盖 Install the 9 pieces of screw + 4 pieces of soft cover. 24。把面包机盖装好 Install the cover back. 25。锁上面包机低最后的一个长螺丝，完成！ Finally, fix the last screw at the bottom of the bread maker.