У нас вы можете посмотреть бесплатно New Version EPX10000 Long Range Metal Detector Underground Metal Detector Depth 5-50m или скачать в максимальном доступном качестве, которое было загружено на ютуб. Для скачивания выберите вариант из формы ниже:
Если кнопки скачивания не
загрузились
НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием, пожалуйста напишите в поддержку по адресу внизу
страницы.
Спасибо за использование сервиса savevideohd.ru
New Version EPX10000 Long Range Metal Detector Underground Metal Detector Depth 5-50m Technical parameters 1.Detection depth range:5-50m 2. Detection distance range :100-1000m 3.Rechargeable battery:8 hours of continuous work 4.Voltage:12VDC 5.Temperature range:45℃ to 85℃ 6.Humidity:0~95%(non condensing) 7.16 bit processor speed,40MIPS –16MHz 8.32 bit DSS synthesis chip,wave from output 9.Digital frequency synthesisX20PLL,automatic frequency stabilizer,0.1MHz 10.Color LCD display,a resolution of 480 x 320 pixels 11.Net weight:6.6kg,Gross weight:10.5kg 12.Product size:47X37X13.5cm INSTALLATION Scanner control installation Note: Before the daily operation, the battery must be fully charged! If you do not charge it, the EPX10000 might go wrong. If abnormal , this may be the first time warning that the battery power is too low and must be charged. If the battery power is charged a whole night, after that, the battery is still no power, you need to replace the battery or charger, or AC power outlet without electricity. If the battery is charged,but it is not full of power,you may need to replace the built-in battery. A new fully charged battery can let EPX10000 continue to work about eight hours. Before turning on the scanner, put the EPX10000 transmitter on the ground, the sensor antenna is connected to the corresponding jacks of the transmitter. When open the transmitter,never plug the sensor, if doing it, it will cause damage to the machine. Previously used EPX10000 scan,first make all the necessary connections. 1.The sensor is connected to the scanner testing (+) testing (-) on the jack, insert the probe of sensor on the earth 2.The transmit antenna signal transmission is mounted on the corresponding interface 3. with the power key is turned "On / Off” knob, turn on the power. At this time, in the LCD area, power indicator,horizontal trmming,longitudinal trmming indicator lights. 4. at this time, EPX10000 is scanning all selected element . Before starting the detection process, please let it work 3-5 minutes, which will be briefly explained later. 5.after the end of the operation, remember to turn off EPX10000. For ease to use,the instrument requires the use of a smll battery charger is connected to the power line charg instrument. Receiver - The rotary switch on the top of the receiver panel are the headphone and the antenna jack. When do not use, do not connect the antenna rods with the receiver! If the antenna rod is saved with it inserted in the receiver , it will cause the battery to drain. Receiving antenna rod - rod antenna is designed to point out to the operator that he / she has entered a power transmission line between the sensor and the target. Under normal circumstances, the operator should hand held the antenna rod stably and balanced, as high as your waist, and slightly in front of the operator. When hand held the antenna rods, rod antenna should is pointed to the front and parallel to each other and separated by 8-18 inches away. Everyone needs to find their own best distance. It takes trial and error to find. Please remember, the people who operate this device, calm relaxed person will do better than the tense stiff! When you enter the RF energy line, measured metal,the antenna rod will naturally cross. And the radar scan pointer will stop in one location. When the antenna and radar cross and the scanner pause, you see the dawn of victory would come. Email: [email protected] skype: graigar