Скачать с ютуб Don't want to risk failing Smog? GM Emissions Drive Cycle в хорошем качестве

Don't want to risk failing Smog? GM Emissions Drive Cycle

Need to complete inspection monitors for EVAP, EGR, CAT, o2, or Evap to pass emissions or smog test? This drive works for all GM General Motors vehicles like Chevrolet, Cadillac, Buick, Pontiac, and Oldsmobile. 8 Simple Steps to Setting your inspection monitors with helpful tips including the trick oxygen sensor monitor. ▶️▶️ Link to recommend OBD2 reader https://amzn.to/3SgUTf3 ▶️ 12 Minute Actual Drive    • Smog Drive Cycle COMPLETED within 21 ...   ▶️ 6-step drive cycle    • How To Pass A Smog Test With 6 Steps   ▶️ Actual Smog test performed    • Emissions Drive Cycle Tips & What to ...   ▶️ Demo EMISSION INSPECTION MONITOR Readiness (I/M)    • How to use OBD2 Reader To Check I/M r...   ▶️How to Pass Smog Test, Understand Emissions Drive Cycle To Pass Smog    • How to use OBD2 Reader To Check I/M r...   ▶️ Catalyst monitor not ready?    • Improve Your Catalyst Monitor Readine...   How To Clean Catalytic Converter▶️ P0420 P0430 Fix - no removal    • Clean Catalytic Converter the Easy Wa...   ▶️ Catalyst Monitor Cheat    • Amazing Trick to Get Catalyst Monitor...   ▶️ Catalyst not ready? Watch this video    • Cataclean Review▶️ Catalyst Monitor N...   ▶️ Evap monitor not ready?    • Evap Monitor Not Ready? Evaporative E...   ▶️ EGR monitor not ready?    • How to Get EGR Monitor Ready for Smog...   ▶️ Oxygen sensor not ready?    • Essential tips to prepare your oxygen...   ▶️ Oxygen sensor replacement    • Oxygen Sensor Replacement and What Yo...   ▶️o2 sensor monitor incomplete    • Essential tips to prepare your oxygen...   ▶️updated o2 sensor fixes    • O2 Sensor Monitor Not Ready ▶️ Smog D...   ▶️How To Test Oxygen Sensor Heater Circuit    • H02S Oxygen Sensor Heater Is Not Read...   ▶️ Oxygen sensor heater element testing    • How To Test Oxygen Sensor Heater▶️ o2...   ▶️How to use OBD2 Reader To Check I/M Readiness to Pass Smog Check    • How to use OBD2 Reader To Check I/M r...   ▶️ 2024 update Get CAT Monitor Ready FAST!    • Get CAT Monitor Ready FAST! An Old Sm...   ▶️Does Cataclean Work? Failed Smog, Bad Catalyst, P420 P430 P431    • Does Cataclean Work? Failed Smog, Bad...   ▶️Catalytic Converter Cleaner? P420 Fix? - Should You Use CRC Emission System Cleaner?    • I Tested Guaranteed To Pass Catalytic...   ▶️P420 Smog Failure? Watch to See if Dura Lube Catalytic Converter Treatment Can Help    • P420 Smog Failure? Watch to See if Du...   ▶️2024 update How to look up state Inspection Monitor Requirements. I/M monitors status codes    • Why State Inspections Are A JOKE (Ins...   ▶️what is a PENDING DTC    • Why Your Car Says "PENDING" Codes (an...   ▶️What is a STORED DTC    • What is a stored DTC code? Stored fau...   ▶️What is a PERMANENT DTC    • Removing Permanent Trouble Codes! How...   ▶️pending vs stored vs permanent explained    • Diagnostic Trouble Code? Pending vs S...   ▶️Permanent DTC long video    • Clear Permanent Codes by doing this w...   ▶️Reset check engine light without any tools    • How to Reset Check Engine Without Too...   Products ▶️Fuel Treatment https://amzn.to/38p7Ps6 ▶️Car Memory / Data Saver https://amzn.to/3mCTpKd . Drive Cycle 1. Cold Start. In order to be classified as a cold start the engine coolant temperature must be below 50°C (122°F) and within 6°C (11°F) of the outside air temperature at startup. Do not leave the key on prior to the cold start or the heated oxygen sensor diagnostic will not run. 2. Idle. The engine must be run for two and a half minutes with the air conditioner on + rear defroster “on”. The more electrical load you can apply the better, so turn on the headlights as well. 3. Accelerate. Turn “off” the air conditioner and all the other loads and apply half throttle until 55 m.p.h. or 88kph 4. Hold Steady Speed. Maintain a steady speed of 55mph for 3 minutes. 5. Decelerate. Let off the accelerator pedal. Do not shift, “touch” the brake or clutch. It is important to let the vehicle coast along gradually slowing down to under 20 mph or 32 kph. 6. Accelerate. Accelerate at 3/4 throttle until 55-60mph or 88-96 KPH This will perform the same diagnostics as in step three 7. Hold Steady Speed. Hold a steady speed of 55mph or 88 kph for five minutes. 8. Decelerate. This will perform the same diagnostics as in step 5. Again, don't touch the clutch or brakes or shift gears. The video includes a guide how the actual inspection monitors are set for your GM vehicle. Disclaimer: Due to factors beyond the control of RandomFix, RandomFix assumes no liability. Affiliate Partner: I receive a fee from some of my affiliate partners for my first-hand recommendations. 0:00 Intro to GM drive cycle 0:38 Overview of GM drive cycle procedure for emissions testing, including vocabulary, safety, and OBD2 diagnostics. 5:28 Overview of GM emissions drive cycle and readiness monitors for smog test preparation. 10:21 Summary of GM vehicle emissions drive cycle procedure for smog test readiness. 15:12 Understanding the GM emissions drive cycle is crucial for passing smog tests and ensuring all monitors are ready for vehicle sale or registration renewal. 20:32 Understanding GM vehicle emissions systems, including oxygen sensors, catalytic converters, and tips for passing the emissions test. 25:28 Tips for passing smog test for GM vehicles, including checking engine light, tires, and fuel additives. 30:13 Tips for DIY vehicle maintenance and emissions system care to save money and gain confidence in car repair.