Скачать с ютуб Asus ZenFone 3 Display Assembly Repair - Fixez.com в хорошем качестве

Asus ZenFone 3 Display Assembly Repair - Fixez.com

Asus ZenFone 3 Replacement Screen: http://bit.ly/2o3XBpp Asus ZenFone 3 DIY Repair Tools: http://bit.ly/2lzLIop Watch the Official Asus ZenFone 3 Display Assembly Repair Guide. Following the step-by-step ZenFone 3 screen replacement instructions we have provided will help you safely replace a damaged or faulty 5.5" Asus screen. Visit Fixez.com for all of the DIY Asus ZenFone 3 replacement screens, parts and tools you need to fix your phone quickly, and affordably. If you need your ZenFone 3 repaired ASAP instead- we have you covered there too. Contact one of our skilled technicians at 866-233-6460 or [email protected] and they will fix your device for you. They are available Monday - Friday, 9am to 5pm PST. Subscribe to our YouTube Channel for additional DIY smartphone and tablet teardown and repair videos!    / @fixez   Like us on Facebook:   / fixez.com   Follow us on Twitter:   / fixezdotcom   Asus ZenFone 3 Display Assembly Repair Video Steps: Warning: You are performing this repair at your own risk We claim no responsibility for any damages that might occur Step 1 Power down your Asus smartphone. Step 2 (Asus ZenFone 3 SIM card and microSD Card Tray) Eject the SIM card and microSD Card Tray. Step 3 (Asus ZenFone 3 Rear Glass Panel) The ZenFone 3 rear glass panel is glued on solidly and is a tight fit within the narrow bezel. Apply heat to soften the adhesive. With the precision knife create enough space to insert a playing card. Attack the adhesive and carefully dislodge the 2.5D corning gorilla glass rear panel from the phone. Step 4 (Asus ZenFone 3 Exterior Midframe, Fingerprint Sensor, and Loudspeaker) Remove the following 19 Phillips screws. Detach the fingerprint sensor cable and signal cable from the ZenFone 3 motherboard. Use the spudger to pry up the plastic exterior midframe. It includes the ZenFone 3 fingerprint sensor and rear camera lens cover. Extricate the Asus ZenFone 3 loudspeaker module from the bottom of the phone. Step 5 (Asus ZenFone 3 USB-C Port/Daughterboard, Signal Cable, and Vibrator) Detach the ZenFone 3 battery connector from the motherboard. Extract the signal cable from the side of the interior midframe. Peel up the piece of Kaptan tape and disconnect the display cable from the daughterboard. Detach the interconnect cable. Remove the following Phillips screw. Remove the daughterboard from the Asus phone. It includes the Zenfone 3 USB-C port, primary microphone, vibrator, spring contacts, and some control hardware. Step 6 (Asus ZenFone 3 Battery) Locate the two peel-to-remove adhesive tabs at the bottom of the ZenFone 3 battery. Grab the first tab and try to keep the adhesive strip flat and wide. Slowly and gently pull each strip up and away from the Asus smartphone. The strips will stretch to many times the length of the battery- keep pulling until they come out from between the battery and the midframe. And just like that, out pops the 3,000 milliampere-hour (mAh), 3.85-volt Asus ZenFone 3 battery. Step 7 (Asus ZenFone 3 Motherboard) Disconnect the bevy of cables from the Asus ZenFone 3 motherboard. Remove the following 3 Phillips screws. Carefully free the motherboard from the gob of thermal paste securing it to the Asus phone. Step 8 (Asus ZenFone 3 Headphone Jack and Microphone Assembly, Earpiece Speaker, and Rear-Facing Camera) Remove the following Phillips screw. With the tweezers in hand, pry the 3.5mm headphone jack and microphone assembly up and away from the chassis. Tweeze out the spring-contact-connected ZenFone 3 earpiece speaker. Remove the 16-megapixel Asus ZenFone 3 rear-facing camera with the latest Sony IMX298 sensor. Step 9 (Asus ZenFone 3 Display Assembly) Peel the digitizer cable up from the Asus midframe. Begin to free the 5.5-inch ZenFone 3 display assembly by using the heat gun to warm up the adhesive securing it to the interior midframe. With the precision knife create enough space to insert a playing card. Use the playing card to attack the sticky adhesive. Take your time and apply additional heat as needed. Once you have sliced through the adhesive, be mindful of the display’s cables when decoupling the Asus ZenFone 3 screen from the frame. * To reassemble your device, follow the steps in reverse order.