Скачать с ютуб Honda Ruckus Valve Adjustment Overview в хорошем качестве

Honda Ruckus Valve Adjustment Overview

NOTE: There is a DEBATE on my "Dead Cold Motor" for the valves. This is the best way from my experience to get a consistent result when you do your valves. IF you feel you can not do this correctly and you are in Houston my brother and I can do this for you (for a fee) so please contact me if you want this done. 00:00 Introduction and what we are doing in this video 00:21 Disclaimer 00:33 Symptoms 01:18 GET Motor 01:46 BEGIN Adjustment section 01:51 TOOL / SUPPLIES you will need 04:48 Remove the Valve Cover 05:22 Set the motor to TDC 06:41 Valve lash specs for the Honda GET 49cc 07:43 INTAKE How to move and change the shim 09:07 Why the Magnet on a stick? 09:40 EXHAUST How to move and change the shim 10:28 Measure the GAP with shims - See description for more details 12:35 Rotate and test over and over again to ensure the correct lash 13:38 Warning to CDI users (Removal of rev limit) 14:44 Put the Valve cover back on 15:19 Final thoughts 16:01 BLOOPERS COLD MOTOR before you start! NOTE: There is a DEBATE on my "Dead Cold Motor" for the valves. This is the best way from my experience to get a consistent result when you do your valves but by all means, explain why you warm your motor in the comments. GOAL: The goal of all of this is to have the valve last match the numbers below but change the shim to the correct size. When you measure if it's too tight try a thinner shim, if it's too loose try a wider shim. Use math if you need to. Example: INTAKE measures .15 on the feeler gauge. Remove the shim and measure it with the caliper. Your caliper reads 1.50. Since it is too WIDE your shim should be .05 thinner. Open your shim kit and take out 1.45 and install it. Now your .10 feeler should be good (Barley dragging as you pass it in the gap). Valve lash is to wide math: Measured .15 - spec of .10 = .05 to WIDE Shim is 1.50 - .05 = 1.45 (new shim size) Valve last is too skinny math: Measured .05 - spec of .10 = -.05 (If its negative its to skinny) Shim is 1.50 - -.05 = 1.55 (remember minus a negative can be changed to plus a positive) INTAKE VALVE LASH: .004 inches / .10 mm EXHAUST VALVE LASH: .007 inches / .19 mm Tools I used: *Caliper https://amzn.to/3yDghkZ *7.48 OD Shims https://amzn.to/3Iy5cpB *Feeler gauges https://amzn.to/3RuQVy4 *Magnet Stick https://amzn.to/3IvgCKS VOSS HELMETS! 10% off or CODE "SMALLENGINEVELOCITY" https://www.vosshelmetsusa.com/smalle... Join this channel to get access to perks:    / @smallenginevelocity   OFFICIAL SEV STORE: (NEW) https://www.smallenginevelocity.com/ Better pricing and way better shipping cost NOTE: I am not an expert but more of an enthusiast who is trying to build experience. Please feel free to ask questions in the comments or resources like 49ccScoot forums on the internet (Great Place!) For China bikes for SURE go to Chinariders.Net Facebook [Give me a like] facebook.com/SmallEngineVelocity/ Instagram @SmallEngineVelocity Canon EOS M50 with EF-M 15-45mm (My camera) https://amzn.to/31tBook Movo VXR10 Hot Shoe Directional Mic (My Mic) The best sound of ALL the mics I've purchased https://amzn.to/31Db0bM GoPro Hero 7 Black Just go with the best. It's worth it https://amzn.to/2IBxJwa