У нас вы можете посмотреть бесплатно Tarot FY680 Build - Electronics - eRC или скачать в максимальном доступном качестве, которое было загружено на ютуб. Для скачивания выберите вариант из формы ниже:
Если кнопки скачивания не
загрузились
НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием, пожалуйста напишите в поддержку по адресу внизу
страницы.
Спасибо за использование сервиса savevideohd.ru
*** Coupon Code: DEANFY680SDJIUY582 Discount (3,5%) on: Tarot FY680 Frame: http://www.foxtechfpv.com/tarot-fy680... 1255 Supreme Lite Propellers: http://www.foxtechfpv.com/foxtech-sup... Foxtech 40A OPTO ESCs: http://www.foxtechfpv.com/foxtech-mul... Foxtech S2216 800 KV Motors: http://www.foxtechfpv.com/foxtech-mot... *** This is second video in my Tarot FY680 Build series and it's all about power system and electronics. This is also my longest video ever packed with tons of information and tips. This video covers rest of the build except propellers installation and it is most intimidating part of the build. You have to solder, route and organize wires, connect stuff... I hope this video will help you make multi-rotor builds an enjoyable and pleasant experience, rather that frustrating one. Here is couple of eRC tips and tricks that will help you with electronics and power system builds in the future: 1. Always use Threadlocker when you have metal on metal contact, especially when mounting motors. 2. Set your soldering iron to about 370 °C. This is enough to work with thick 12 AWG wires, but it's not too much to damage sensitive power distribution boards. 3. Always use soldering paste. This helps creating good, long lasting solder joint. 4. Always tin wires, PCB boards and connectors before final soldering. This helps creating good, long lasting solder joint. Do this even if there's already a solder on the board. It's usually not the same type as yours so make sure you tin everything with your own solder. 5. If your Zip Ties are too short, use two to make them longer. 6. Add additional 26 AWG JST connections to the main power distribution board so that you have easy access to the main pack voltage for future accessories like LED's, FPV, Gimbal, Pivot Landing Gear etc. 7. Use heat-shrink tubing on connections that go into carbon fiber tubes to prevent accidental shorts. 8. Plug Male and Female connectors together before soldering whenever possible to prevent connector warping and plastic melting due to heat. This helps keeping contacts in place and increases heat dissipation. 9. Use multiple layers of double-sided tape when mounting main flight controller to increase vibration dampening. You need: DJI Naza V2 Full Set: http://www.foxtechfpv.com/dji-nazam-v... Foxtech 40A OPTO ESCs: http://www.foxtechfpv.com/foxtech-mul... Foxtech S3508 700 KV Motors: http://www.foxtechfpv.com/foxtech-mot... Futaba R7008SB Receiver: http://www.foxtechfpv.com/futaba-r700... Accessories: 30 cm Servo Extension Leads 12 AWG and 14 AWG Wires Servo Wire Threadlocker (medium strength) Double-sided Tape Zip Ties Antenna Tubing Heat-shrink Tubing Pipe Clip Male and Female JST Connectors Male XT-60 Connector 3.5 mm Bullet Connectors Tarot Power Distribution Board Tools: Soldering Station 60/40 Solder Soldering Paste Third Hand Lighter Crimping Tool 2.0 mm Hex Screwdriver 3.0 mm Phillips Screwdriver Precision Knife Additional Information: Video: Canon 600D/T3i - 18-55 mm Lens Editing: FinalCut Pro X Music: GarageBand